Modern Automotive Performance
Modern Automotive Performance

Popular Applications

Radium Engineering Catch Can for Evolution X

Posted on 26 February 2014

This Radium Installation kit was specifically designed for the 2008+ Mitsubishi Lancer Evolution X.

An oil catch can is essential on a performance vehicle to protect the engine from elevated levels of crankcase blow-by accumulated from aggressive driving. Excess oil saturated air circulating back into the air intake stream can lead to poor performance.
radium engineering-auto-catch-can1-flow-chart

Unlike many catch cans on the market, this catch can features an integrated oil separator that accelerates oil condensation. This cleans the PCV gasses and reduces the oil build-up on the inside of the intake tract and intake manifold and intercooler.The stainless steel filtration media is cleanable and reuseable. The catch cans act as a filter and collect the oil and other sludge and keep it out of vital engine components. radium-auto-catch-can2  

Read about all the benefits and functionality of the Radium Engineering's popular catch cans here: http://radiumauto.com/media/blog-page.php?Product-Insight-Radium-Oil-Catch-Cans-25 Features: -Effectively raises the octane and increased engine performance from cleaner inlet air -Prevents oil buildup in the intake or intercooler system walls, throttle body, intake manifold, etc. -Excessive oil collection can be an indicator of a damaged engine. -Lowers hydrocarbon emissions -Capacity: 6 fluid ounces -Height (without fittings): 5 inches -Outside Diameter: 2.45 inches EVO X CATCH CAN KIT DETAILS Radium Engineering offers two completely independent oil catch can kits for the Evo X that are sold individually or together using the drop down menu above. They do NOT vent to atmosphere (VTA), thus are emissions and track legal. Closed loop systems route clean filtered air back in through the engine to be burned and to promote negative crankcase pressure for optimal performance. Furthermore, closed systems prevent unwanted oil vapors into the cabin. The PCV Catch Can Kit (shown below) installs immediately behind the RH headlight and plumbs in-line with the PCV hose. When the intake manifold pressure is close to or greater than atmospheric pressure, the PCV "check" valve closes and, thus, this hose experiences no flow. Conversely, the PCV hose will experience "metered" vacuum when the engine is idling, steady state cruising, and decelerating. This would normally draw unwanted crankcase vapor, unspent fuel, and oil sludge into the intake manifold immediately after a high load run. Note: Because the Radium Engineering catch cans are pressure sealed, they are great for boosted applications as well so connecting to the intake manifold is permitted and will withstand any boost level. radium-auto-catch-can3   radium-auto-catch-can4-install-review   The Crank Case Catch Can Kit (shown below) installs immediately behind the LH headlight and plumbs in-line with the crank case vent hose. This is the hose that connects from the port on the valve cover to the turbo air intake pipe. During low engine loads, this hose experiences atmospheric pressure, but when the engine is at high load (WOT), this hose will experience vacuum and would normally be drawing unwanted crankcase vapors, unspent fuel, and oil sludge into the air filter intake pipe, turbocharger compressor and intercooler system. The Radium Engineering oil catch can keeps that from happening. radium-auto-catch-can6-install-review radium-auto-catch-can5   For the ultimate in engine protection, Radium recommends installing both catch can kits. PCV Kit Includes: -Radium billet oil catch can with integrated condenser and dipstick -Radium laser cut powder coated application specific mounting bracket -Anodized aluminum hose ends and adapter fittings -Rubber hose to mate to custom applications -Stainless steel mounting hardware Crank Case Vent Kit Includes: -Radium billet oil catch can with integrated condenser and dipstick -Radium laser cut powder coated application specific mounting bracket -Anodized aluminum hose ends and adapter fittings -Rubber hose to mate to custom applications -Stainless steel mounting hardware

PETCOCK DRAIN KIT OPTION

-Anodized -4AN O-ring barbed fitting -Nylon ¼” barb mini ball valve -6ft high temperature rated 1/4" rubber hose This kit, sold seperately, can be used to remotely drain the catch cans without the need to unscrew the canister body.
radium-auto-catch-can7
  The billet Catch Can is available at MAPerformance direct from Radium Engineering starting at $199.95 Item Number: 20-01051

More Posts

10 comments

  • Sean Riley: November 10, 2015

    Price?

  • Miguel Angel Hernandez: November 10, 2015

    Nicely engineered! You’ll be seeing an order from me soon! Do you have an Instagram, so I give shout outs?

  • Jake Smithson: November 10, 2015

    That’s sleek lookin

  • Michael Savannah: November 10, 2015

    Any plans for a Evo IX kit?

  • Modern Automotive Performance: November 10, 2015

    You may find us on Instagram here: http://instagram.com/maperformance

  • Sean Riley: November 10, 2015

    I’m gonna say just 1, there pretty nice catch cans, even the somewhat shitty ones are like a 100

  • Modern Automotive Performance: November 10, 2015

    They start at 199.99!!!

  • Jowell Protasio: November 10, 2015

    So the price is for both kit or just one? If its both, thats a steal!!

  • Patrick Widner: November 10, 2015

    Nice. If I hadn’t just made my own versions of these from Moroso cans and AN braided hosing I would be all over this!

  • Ryan Flor: November 10, 2015

    Want!

Leave a comment

All blog comments are checked prior to publishing

SEARCH OUR STORE